Just how to Replace a Bathtub ( Guide).
Just how to Replace a Bathtub ( Guide).
Blog Article
What're your ideas about How to Install a Bathtub?
Installing a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bathtub with a new one is also a reasonably tough job. If the old bathtub is readily easily accessible, the project can move easily; if you need to open a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task as well as fit trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is far better to take into consideration employing one before you begin. Possibilities are you may need an expert plumber to make tube links.
This post will certainly aid you mount a brand-new bath tub in your washroom if you have currently bought a new tub and don't require to change the plan of your previous water system pipelines.
Your tools and material checklist should comprise the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Before carrying on to fit the new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin making certain that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is safely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former kind ought to be attached to the tap ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wooden boards are practical in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the tub till the spirit level checks out degree.
To install faucets, fit all-time low of the furthest adaptable tap adapter to the proper supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Activate the water supply and inspect all joints and also brand-new pipework for leaks and tighten them if required. Load the bath tub and also check the overflow outlet as well as the regular electrical outlet for leaks.
Finally, repair the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub ought to wait up until the tub has been utilized a minimum of once as this will settle it right into its last placement.
Getting ready for the Setup
First of all, the sustaining framework provided with the bathroom must be fitted (if called for) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the tap comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break a rigid seal, creating the water to permeate the wall surface in between the bath and also the tiling, resulting in complications with wetness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your components as well as installations. They are offered in tubes and cartridges, and also can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealer can crack relatively very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using waterproof or water-proof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate more info about How to Install a Bathtub Yourself? Try to leave a remark further down. We would be interested to see your thinking about this post. We are looking forward that you come back again soon. Remember to set aside a second to share this blog entry if you liked it. I truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Visit Our Website Report this page